NH35 vs Miyota 8215 vs 2813 vs 2836: which movement for your build?

The four movements most builders choose between, side by side: specs, where the sources disagree, and which one suits a vintage or a modern build.

Asian 2813 movement (left) and Asian 2836 day-date movement (right) side by side

My 2813 vs 2836 comparison is one of the most read pages on this site, but most people starting a build today are also weighing up the Seiko NH35 and the Miyota 8215. So here are all four side by side: the specs, where each one shines, and which I'd pick for different kinds of build.

One warning before the table. Specs for these movements are messier than you'd expect. Seiko and Miyota publish official figures, but the 2813 and 2836 are Chinese clones made by several factories, and the published figures often disagree. Where they do, I've said so rather than pick a number.

Spec comparison table

SpecSeiko NH35Miyota 8215Asian 2813Asian 2836
Beat rate21,600 bph (6 bps)21,600 bph (6 bps)21,600 bph (6 bps)28,800 bph (8 bps), but some clones run at 21,600
Jewels24 (Seiko/TMI technical guide)2121 or 22 (figures vary)Varies by maker
Power reserveMore than 41 h (TMI minimum)About 42 hRoughly 36–40 h (figures vary)About 38–42 h (ETA figures; clones vary)
HackingYesDisputed: see belowYesVaries: see below
Hand-windingYesYesYesYes
QuicksetDateDateDateDay and date
Size27.40 × 5.32 mm (29.36 mm with dial spacer)26 × 5.67 mm25.6–26 × 5.4 mm25.6 × 5.05 mm
Accuracy spec−20/+40 s/day (TMI, static, three positions)−20/+40 s/day±60 s/day (unconfirmed)None published
Hand holes (hour/min/sec)1.5 / 0.88 / 0.2 (retailer figures)1.50 / 1.00 / 0.171.50 / 1.00 / 0.171.50 / 0.90 / 0.25
Typical priceAbout £40–60 (UK eBay asking prices, 2026)About $40–60About $10–40About $40–70

The 8215 and NH35 figures are the makers' own, apart from the NH35 hand sizes, which are seller figures rather than Seiko's. The non-NH35 prices are rough US dollar figures. The 2813 and 2836 hand sizes and prices are the ones from my own movement reviews. The full hand size list is on my watch hand sizes chart.

The only movement I've properly timed is my first 2813: about +15–20 s/day out of the box, settling at about +5 after regulating. My other builds keep good enough time on the wrist that I haven't put them on the app.

Where the figures disagree

  • Miyota 8215 hacking. Miyota's current spec page lists a stop seconds device, yet plenty of listings say the 8215 doesn't hack, and my own 8215 review says the same about mine. The likely explanation is that the 8200 family was non-hacking for decades and Miyota added hacking around 2018–19, so older stock still in circulation won't hack. Pull the crown out and watch the seconds hand. Neither result means your movement is broken.
  • 2836 clone hacking and beat rate. The genuine ETA 2836-2 runs at 28,800 bph and has a stop seconds device, though ETA's own documents list it as optional. Sea-Gull's ST2130 is usually listed as hacking too. For the cheap "2836" clones sold on eBay and AliExpress, listings are unreliable either way, and some Asian "2824/2836" clones run at 21,600 rather than 28,800. The "2824" clone in my aged Explorer build turned out to be one of them. Check yours with a timegrapher app before you build.
  • 2813 hand sizes. My own measurements give 1.50/1.00/0.17 mm (the hour hand is really 1.52, but 1.50 fits), and most listings agree. Some list 1.35/0.85/0.25, which doesn't match. I'd go with 1.50/1.00/0.17.
  • NH35 accuracy and jewels. TMI rates the NH35A at −20/+40 s/day, while Seiko's own 4R35 is rated −35/+45. That TMI figure is a static test: measured 10–60 minutes after a full wind, with the calendar disengaged, in only three positions, at a 53° lift angle. The technical guide gives 24 jewels, though some listings say 23. Its power reserve is "more than 41 hours", which is a minimum, not a typical figure.
  • NH35 hand sizes. You'll often see 1.50 / 0.90 / 0.20 quoted, though some sellers list the minute hole as 0.88 mm (hour 1.5, seconds 0.2). These are seller figures, not Seiko's.
  • 2813 lineage and power reserve. The DG2813 is often called a straight clone of the Miyota 8215, but it's more accurate to say it uses the 8200-family layout without being a direct clone, with different dial feet. Power reserve figures vary from about 36 h to 40 h or more. It runs at 21,600 bph, the same as the NH35, not 28,800.

Get a Timegrapher

Asian 2813 movement (left) and Asian 2836 day-date movement (right) side by side, dial side up

Seiko NH35: the modder's default

The NH35 is widely treated as Seiko's 4R35 sold without branding through TMI. Seiko's technical guide gives it 21,600 vph, 24 jewels, a 27.40 mm diameter, 5.32 mm height and "more than 41 hours" of reserve. It hacks, hand-winds, has a quickset date and is known as a tough, forgiving movement. Its biggest strength isn't the movement itself, though; it's the parts ecosystem. NH35 dials, hands, cases, date wheels and chapter rings are everywhere, from specialist mod shops to AliExpress, because the Seiko modding scene is built around it. The NH36 adds a day. The NH34 adds a GMT hand, but it's a "caller" GMT: by Seiko's crown table the first click sets the 24-hour hand, and the local hour hand doesn't jump on its own.

If you're fitting a dial, the feet positions depend on where the crown sits. For a 3 o'clock crown, keep the feet at the 8- and 38-minute positions; for a 4 o'clock (SKX-style) crown, keep 12 and 42. That's the usual guidance from dial sellers rather than a Seiko figure.

The downsides for this site's kind of build: at 27.4 mm it's wider than the others, so it needs NH-specific cases and dials (usually 28.5 mm), and NH35 parts won't cross over to a 2824-style case. It's also a 6 bps movement, so the seconds sweep isn't as smooth as a 2836. On price, loose NH35As were listed on UK eBay at roughly £40–60 in 2026 (asking prices).

I haven't built with an NH35 yet. It's popular for Seiko-style mods, but the cases and dials I use for my builds are made for the 2824/2813 size, so it hasn't fitted my plans.

Seiko NH35 movement, dial side, showing the date wheel, with a clear plastic stem protector fittedSeiko NH35 movement, rotor side, in its black plastic movement holder

Get NH35 Movement

Miyota 8215: the quality budget pick

The 8215 is a genuine Japanese movement from Citizen's Miyota, used in plenty of affordable watches. It's the one I'd call the best made of the four for the money: the date change is smooth, the parts feel properly finished, and it has an official −20/+40 s/day spec. Hand sizes match the 2813, so 2813 hands fit.

The downsides: it's the tallest here at 5.67 mm, so it needs a different spacer and often a deeper case than a 2824 or 2836. The rotor is famously noisy. The seconds hand can show a slight stutter on some examples, and older stock doesn't hack. See my full Miyota 8215 review.

Miyota 8215 automatic movement, dial side, showing the white date wheel and stem

Get Miyota 8215 Movement

Asian 2813: the cheap learner

The DG2813 is a Chinese movement built on the Miyota 8200-family layout, which is why it shares the 8215's hand sizes and roughly its dimensions. It's the cheapest way into building, it hacks, and it's easy to get the stem out. That makes it perfect for a first build or for practice.

The trade-offs are quality control and refinement. Several factories make it, there's little consistency, it's noisy, the 0.17 mm seconds pin is easy to damage, and the unconfirmed ±60 s/day spec says a lot. When one goes wrong, it's usually cheaper to replace than to fix; I cover that in service or replace a 2813. Full details are in my 2813 review.

Get Hand Pressers

Get 2813 Movement

Asian 2836: the smooth 8 bps option

The Asian 2836 is a copy of the ETA 2836-2 day-date. When it runs at 28,800 bph it gives the smoothest sweep of the four, which is what most modern Swiss watches have. It's also 25.6 mm across, the same as a 2824, so 2824-sized cases and spacers work, and the 0.25 mm seconds pin is much easier to fit than the 0.17 mm pins on the 2813 and 8215.

The downsides: it's one of the more expensive options here, and the day wheel is wasted if your build only shows the date. Its date wheel sits above the movement, which makes date wheel overlays easier than on a 2824. If you want 8 bps without a day function, the Asian 2824 is the date-only sibling. See my full 2836 review.

Buy 2836 Movement

Get 2824 Movement

Vintage-style vs modern builds

Beat rate is the easiest way to split these. A 6 bps movement (NH35, 8215, 2813) has a slightly stepped sweep, which suits a vintage homage, because the older watches those builds are based on beat more slowly than today's 28,800 bph movements. I used a 2813 in my Submariner 5513 build, an 8215 in the Explorer 1016 build, and a 21,600 bph "2824" clone in the aged Explorer build.

For a modern-looking build, an 8 bps 2836 or 2824 gives the smoother sweep people expect from a current sports watch. It's a small visual detail, but you notice it once you've seen both side by side.

Get 2836 Movement

On my 5513 and Explorer builds the slower 6 bps sweep actually suits the look. You can see the seconds hand step more than on my 2836 Datejust, but on a vintage-style watch it feels right.

Parts availability

This is where the NH35 wins easily. It has the largest mod ecosystem by a long way, and many specialist dial and case makers design for it first. The 2824/2836 family is next, with a lot of homage cases, dials and date wheels built around it. The 8215 and 2813 share enough to be grouped together, but there are fewer parts made specifically for them.

Get an NH35 Dial

Whatever you choose, don't trust "fits NH35/2824/8215" claims. Dial feet positions differ between these movements, and "universal" dials often don't line up. I go into this in where to buy watch parts in the UK and casing a movement.

Get a Movement Holder

Get Cutting Pliers

Which should you pick?

  • Your first build, or practice: the 2813. It's cheap enough to make mistakes on.
  • The widest choice of parts: the NH35, as long as you want an NH-sized case and dial.
  • A reliable vintage-style homage: the Miyota 8215. Just check the case depth and dial feet first.
  • A modern look with a smooth sweep, or a day-date: the 2836. Use a 2824 if you only want the date.
  • Upgrading an existing 2813 build: an 8215 is the logical step, but it's not always a drop-in swap.

Get 2813 Movement

If you're still unsure, start with my first watch build guide, which explains why the movement is the first thing to choose.

For my next vintage build I'd go with the Miyota 8215 again. It's the best quality of the budget options, and a genuine Japanese movement suits a watch I want to keep.